Hello,
We are having a lot of trouble trying to get pxe imaging working from our WDS server on different subnets. We have an existing Zenworking imaging setup working as of right now, but WDS is causing more issues than I care to troubleshoot. I have read blog after blog, forum post after forum post and everyone says just install it and it works! I guess we have run into some sort of problem that nobody else has.
Enviroment:
2x DC's, Server 2012 R2, both run DNS, 10.5.0.101, 10.5.0.102
1x DHCP Server, 2012 R2, 10.5.0.105
1x WDS Server, 2012 R2, 10.5.0.41
If I put a client on the same subnet as all of the servers it seems to work, except for the fact that it takes a while for the client to get an IP and continue to load wdsnbp.com. I would say around 20-30 seconds. In our zenworks enviroment it takes no more than 1 second to get an IP. As for the dhcp server itself, clients receive normal dhcp offers instantly. So that part is working properly.
Now when I try an access the WDS pxe server from a different subnet other than the one that all of the servers are on, noting that I do have the ip helper address setup on our layer 3 switch:
interface Vlan2025
ip address 10.200.20.1 255.255.255.0
ip helper-address 10.5.0.105
ip helper-address 10.5.0.41
It always says failed to receive boot file. But as I said earlier, clients in windows receive dhcp leases from 10.5.0.105 without issue.
Setting the client options in the DHCP server with options 66 and 67 works sortof, but we found that it was unreliable and often finicky. Like having the system repeatedly ask to press f12, and even if you did press f12 it would still ask to press f12 again.
So I continued to do a wirehark packet capture on the port where the device was trying to get the dhcp/pxe info from the DHCP / WDS servers. The first packet here is from the DHCP server and the second is from the WDS server.
Bootstrap Protocol
Message type: Boot Reply (2)
Hardware type: Ethernet (0x01)
Hardware address length: 6
Hops: 0
Transaction ID: 0xd6c565d2
Seconds elapsed: 0
Bootp flags: 0x8000 (Broadcast)
Client IP address: 0.0.0.0 (0.0.0.0)
Your (client) IP address: 10.200.20.117 (10.200.20.117)
Next server IP address: 10.5.0.105 (10.5.0.105)
Relay agent IP address: 10.200.20.1 (10.200.20.1)
Client MAC address: Hewlett-_c5:65:d2 (78:e7:d1:c5:65:d2)
Client hardware address padding: 00000000000000000000
Server host name not given
Boot file name not given
Magic cookie: DHCP
Option: (53) DHCP Message Type
Length: 1
DHCP: Offer (2)
Option: (1) Subnet Mask
Length: 4
Subnet Mask: 255.255.255.0 (255.255.255.0)
Option: (58) Renewal Time Value
Length: 4
Renewal Time Value: (21600s) 6 hours
Option: (59) Rebinding Time Value
Length: 4
Rebinding Time Value: (37800s) 10 hours, 30 minutes
Option: (51) IP Address Lease Time
Length: 4
IP Address Lease Time: (43200s) 12 hours
Option: (54) DHCP Server Identifier
Length: 4
DHCP Server Identifier: 10.5.0.105 (10.5.0.105)
Option: (3) Router
Length: 4
Router: 10.200.20.1 (10.200.20.1)
Option: (6) Domain Name Server
Length: 8
Domain Name Server: 10.5.0.101 (10.5.0.101)
Domain Name Server: 10.5.0.102 (10.5.0.102)
Option: (15) Domain Name
Length: 8
Domain Name: domain.com
Option: (255) End
Option End: 255
------------------------------------------------------------------------
Bootstrap Protocol
Message type: Boot Reply (2)
Hardware type: Ethernet (0x01)
Hardware address length: 6
Hops: 0
Transaction ID: 0xd2c565d2
Seconds elapsed: 4
Bootp flags: 0x8000 (Broadcast)
Client IP address: 0.0.0.0 (0.0.0.0)
Your (client) IP address: 0.0.0.0 (0.0.0.0)
Next server IP address: 10.5.0.41 (10.5.0.41)
Relay agent IP address: 10.200.20.1 (10.200.20.1)
Client MAC address: Hewlett-_c5:65:d2 (78:e7:d1:c5:65:d2)
Client hardware address padding: 00000000000000000000
Server host name: wds1.domain.com
Boot file name not given
Magic cookie: DHCP
Option: (54) DHCP Server Identifier
Length: 4
DHCP Server Identifier: 10.5.0.41 (10.5.0.41)
Option: (97) UUID/GUID-based Client Identifier
Length: 17
Client Identifier (UUID): eb8daa31-8e62-11df-bbd8-d1c565d278e7
Option: (60) Vendor class identifier
Length: 9
Vendor class identifier: PXEClient
Option: (53) DHCP Message Type
Length: 1
DHCP: Offer (2)
Option: (255) End
Option End: 255
---------------------------------------------------------------
What I find interesting is that the WDS server is not handing out a boot file name:
"Boot file name not given"
Could this be the reason why we receive the no boot file received error when trying to boot a client into pxe?
The other thing that I noticed was that the WDS server is also responding with the:
" Option: (60) Vendor class identifier
Length: 9
Vendor class identifier: PXEClient
"
Why would it be responding with this, when the dhcp is on a separate server. Is this option only if you have DHCP and WDS on the same server?
Any help would be appreciated as there has been too much time already spent on getting nowhere.
Thanks,
Dan.
We are having a lot of trouble trying to get pxe imaging working from our WDS server on different subnets. We have an existing Zenworking imaging setup working as of right now, but WDS is causing more issues than I care to troubleshoot. I have read blog after blog, forum post after forum post and everyone says just install it and it works! I guess we have run into some sort of problem that nobody else has.
Enviroment:
2x DC's, Server 2012 R2, both run DNS, 10.5.0.101, 10.5.0.102
1x DHCP Server, 2012 R2, 10.5.0.105
1x WDS Server, 2012 R2, 10.5.0.41
If I put a client on the same subnet as all of the servers it seems to work, except for the fact that it takes a while for the client to get an IP and continue to load wdsnbp.com. I would say around 20-30 seconds. In our zenworks enviroment it takes no more than 1 second to get an IP. As for the dhcp server itself, clients receive normal dhcp offers instantly. So that part is working properly.
Now when I try an access the WDS pxe server from a different subnet other than the one that all of the servers are on, noting that I do have the ip helper address setup on our layer 3 switch:
interface Vlan2025
ip address 10.200.20.1 255.255.255.0
ip helper-address 10.5.0.105
ip helper-address 10.5.0.41
It always says failed to receive boot file. But as I said earlier, clients in windows receive dhcp leases from 10.5.0.105 without issue.
Setting the client options in the DHCP server with options 66 and 67 works sortof, but we found that it was unreliable and often finicky. Like having the system repeatedly ask to press f12, and even if you did press f12 it would still ask to press f12 again.
So I continued to do a wirehark packet capture on the port where the device was trying to get the dhcp/pxe info from the DHCP / WDS servers. The first packet here is from the DHCP server and the second is from the WDS server.
Bootstrap Protocol
Message type: Boot Reply (2)
Hardware type: Ethernet (0x01)
Hardware address length: 6
Hops: 0
Transaction ID: 0xd6c565d2
Seconds elapsed: 0
Bootp flags: 0x8000 (Broadcast)
Client IP address: 0.0.0.0 (0.0.0.0)
Your (client) IP address: 10.200.20.117 (10.200.20.117)
Next server IP address: 10.5.0.105 (10.5.0.105)
Relay agent IP address: 10.200.20.1 (10.200.20.1)
Client MAC address: Hewlett-_c5:65:d2 (78:e7:d1:c5:65:d2)
Client hardware address padding: 00000000000000000000
Server host name not given
Boot file name not given
Magic cookie: DHCP
Option: (53) DHCP Message Type
Length: 1
DHCP: Offer (2)
Option: (1) Subnet Mask
Length: 4
Subnet Mask: 255.255.255.0 (255.255.255.0)
Option: (58) Renewal Time Value
Length: 4
Renewal Time Value: (21600s) 6 hours
Option: (59) Rebinding Time Value
Length: 4
Rebinding Time Value: (37800s) 10 hours, 30 minutes
Option: (51) IP Address Lease Time
Length: 4
IP Address Lease Time: (43200s) 12 hours
Option: (54) DHCP Server Identifier
Length: 4
DHCP Server Identifier: 10.5.0.105 (10.5.0.105)
Option: (3) Router
Length: 4
Router: 10.200.20.1 (10.200.20.1)
Option: (6) Domain Name Server
Length: 8
Domain Name Server: 10.5.0.101 (10.5.0.101)
Domain Name Server: 10.5.0.102 (10.5.0.102)
Option: (15) Domain Name
Length: 8
Domain Name: domain.com
Option: (255) End
Option End: 255
------------------------------------------------------------------------
Bootstrap Protocol
Message type: Boot Reply (2)
Hardware type: Ethernet (0x01)
Hardware address length: 6
Hops: 0
Transaction ID: 0xd2c565d2
Seconds elapsed: 4
Bootp flags: 0x8000 (Broadcast)
Client IP address: 0.0.0.0 (0.0.0.0)
Your (client) IP address: 0.0.0.0 (0.0.0.0)
Next server IP address: 10.5.0.41 (10.5.0.41)
Relay agent IP address: 10.200.20.1 (10.200.20.1)
Client MAC address: Hewlett-_c5:65:d2 (78:e7:d1:c5:65:d2)
Client hardware address padding: 00000000000000000000
Server host name: wds1.domain.com
Boot file name not given
Magic cookie: DHCP
Option: (54) DHCP Server Identifier
Length: 4
DHCP Server Identifier: 10.5.0.41 (10.5.0.41)
Option: (97) UUID/GUID-based Client Identifier
Length: 17
Client Identifier (UUID): eb8daa31-8e62-11df-bbd8-d1c565d278e7
Option: (60) Vendor class identifier
Length: 9
Vendor class identifier: PXEClient
Option: (53) DHCP Message Type
Length: 1
DHCP: Offer (2)
Option: (255) End
Option End: 255
---------------------------------------------------------------
What I find interesting is that the WDS server is not handing out a boot file name:
"Boot file name not given"
Could this be the reason why we receive the no boot file received error when trying to boot a client into pxe?
The other thing that I noticed was that the WDS server is also responding with the:
" Option: (60) Vendor class identifier
Length: 9
Vendor class identifier: PXEClient
"
Why would it be responding with this, when the dhcp is on a separate server. Is this option only if you have DHCP and WDS on the same server?
Any help would be appreciated as there has been too much time already spent on getting nowhere.
Thanks,
Dan.